Racking machine maintenance introduction

Racking machine maintenance introduction

The bag puller is a must-have test facility for packaging and large and medium-sized companies to test the material tensile test and test the bearing capacity of the material. Today Haida equipment analyzes the maintenance of the bag puller in daily work:

1 . Routine insurance on daily basis is carried out on site by facility operators

( 1 ) Wipe the equipment before the test, and lubricate and lubricate as required. Check whether the handle position and the manual operation position are correct, flexible, and whether the entire equipment is reliable. Run at low speed to check if the drive is normal.

( 2 ) Pay attention to the sound of operation, temperature, pressure, electrical and instrument signals of the facility, and whether the safety insurance is normal.

( 3 ) After the test, turn off the switch and let the lean handle reach zero. Remove iron scraps and dirt, wipe the oil on the rails and sliding surfaces of the facility, and add fuel. Clean the workplace, rectify attachments and tools.

2 . Zhou Baobao   Zhou Baobao is operated by the pilot facility workers every weekend.

( 1 ) Appearance of the tensile tester: Wipe the rails of the facility, each transmission part and the exposed part, and clean the work site. The interior and exterior are clean and free of dead spots, no rust, and the surrounding environment is clean and tidy.

( 2 ) Actuation of the drive: check the technical condition of each part, tighten the loose parts, and adjust the fit clearance. Check interlocks and safety devices. The transmission sound is normal, safe and reliable.

( 3 ) Electrical system: Wipe the surface of the motor and snake skin to inspect the insulation and ground to achieve integrity, cleanliness and reliability.

(a) a level of maintenance   The first-level maintenance is mainly based on the operators and the maintenance workers. According to the plan, partial dismantlement and inspection of the facilities, cleaning of the prescribed parts, adjustment of the gap between the various parts of the tensile tester, and fastening of various parts of the facility. . The scope of a guarantee should be all the facilities of the company, and strict implementation of key facilities. The purpose of the protagonists of a protection is to reduce the facility wear, eliminate hidden dangers, extend the service life of the facility, and provide guarantees for the facilities in order to complete production tasks during the next guarantee period.

(b) Secondary maintenance   The secondary maintenance is mainly based on maintenance workers, and the operation workers participate in the completion. Two maintenance facilities included in the maintenance plan, bag manufacturers Rally partial disintegration of the facility inspection and repair, change or repair worn parts, cleaning, checking, repairing electrical parts, the state of the art facilities fully meet the prescribed requirements of the standard facilities intact .

2 . Zhou Baobao is operated by the pilot facility workers every weekend.

( 1 ) Appearance of the tensile tester: Wipe the rails of the facility, each transmission part and the exposed part, and clean the work site. The interior and exterior are clean and free of dead spots, no rust, and the surrounding environment is clean and tidy.

( 2 ) Actuation of the drive: check the technical condition of each part, tighten the loose parts, and adjust the fit clearance. Check interlocks and safety devices. The transmission sound is normal, safe and reliable.

( 3 ) Electrical system: Wipe the surface of the motor and snake skin to inspect the insulation and ground to achieve integrity, cleanliness and reliability.

(1) Level 1 maintenance: Level 1 maintenance is mainly based on operators, with the assistance of the maintenance workers, partial dismantling and inspection of the facilities according to the plan, cleaning of the prescribed parts, adjustment of the gaps between the various parts of the tensile testing machine, and tightening of various facilities Parts. . The scope of a guarantee should be all the facilities of the company, and strict implementation of key facilities. The purpose of the protagonists of a protection is to reduce the facility wear, eliminate hidden dangers, extend the service life of the facility, and provide guarantees for the facilities in order to complete production tasks during the next guarantee period.

(b) Secondary maintenance: Secondary maintenance is mainly based on maintenance workers, and the operation workers participate in the completion. The secondary maintenance is included in the maintenance plan of the facility. The bag puller manufacturers perform partial dismantling inspection and repair of the facility, change or repair worn parts, and clean, inspect and repair the electrical parts, so that the technical condition of the facility fully meets the requirements of the standard for the unrestricted facilities. .

More detailed information are welcome to call, the national unified service hotline: 400-0711-808

/0769-89280808

,company website:

Our factory locates at Shenzhen city, size of 13000 square meters, only one hour far from Hongkong by truck. We're good at designing and manufacturing acrylic display, as well as multi-material combined display, with lighting & video player.
Thickness of the Display Rack For Merchandising could be customised, for example 5/10/15/20mm.Also the color of Cosmetic Retail Display Rack, some customers would like blue/red/brown,etc, we Apex could do any design accroding to your request. Not only Retail Display , we also offer Retail Display Cosmetic Display Stand, Acrylic Shoe Rack,Cigarette Display Rack and so many different Electronics Retail Display Rack. we are very looking forward to your inquiry.

Jewelry Display Stand

Jewelry Display,Acrylic Jewelry Rack,Jewelry Display Acrylic,Jewelry Display Stand

Shenzhen Apex Artcrafts Co,.LTD , https://www.apexdisplaycn.com